Search results

Looking at Engine X 250w limited to 25km. But then I saw on YouTube this can be unlocked with a few button presses up to 40-60km depending on weight. Is their anyway to disable the unlock??? Firmware etc..... I'm half thinking of disabling one of the buttons in the display to stop him...

I apricate what your saying... but I did say I knew nothing about these things. Ive asked for advise or alternatives. You have given you point and noted thanks. But you don't need to keep coming back editing your post with more photos. If you have no alternatives or advice to give you have...

HI My son has asked me for the Engwe Engine Pro 2 for christmas he is going on 15. I know very little about ebikes and the availability here in Ireland is not great. Can anyone give me any advise as to the quality of this bike. I have looked at a couple of other slightly cheaper Fat Bikes...

I was trying to extend the motor conector from the box..... did a great neat job... until i droped some solder lol. Didnt relize I could buy extenders. Unfrotunatly Im in Ireland so have to order from the German warehouse and they are out of stock for the rear motor.. They only have in stock...

https://amzn.eu/d/3VoUb4u What about this? I stupidly dropped some solder on inside while extending wires. Didnt notice and plugged in and got fried unfortunately. Il extend outside the box next time lol.... So Im worried my Dashi c500 display wont work with a generic controller. So what...

Thanks Thats the controller there in picture. Put ive seen other controllers a third of the price. Just dont have the 9 pin motor conector on them. Was going to pick one up on amazon and splice 9 pin into wires on other controller. Its a brushless 36v 350w motor. Yose Power. Thanks... oh and...

Ok need to explain title a little better. Basicly I need a new controller. My motor is 9 pin 350w 36v. I was looking at the 9 pin controllers and they are a lot more expensive and usually shipped from China. Saw a few controllers on Amazon for half the price they where for 36v motors also but...

At zero im getting .8 v and full just over 4 v. Wiring is corect. Signal to signal on control box and vcc and ground. Motor works fine and engages with pedal assist, but nothing when press throttle.

Hi could you private message me to help please with settings since you have same kit. Thanks Ive tried settings but nothing seems to work. On your yose kit. Did you need to pedal first to activate throttle? Thanks Ive only been testing it on a bench setup up. Throttle appears to be wired...

What does 2.4.4 mean? I went into advanced settings and change HND to Y for voth HND settings. Is there another setting?

Yes changed both settings to n. I could be wrong but once throttle is wired right shouldnt it just work. They are very easy design and work similarly feedback voltage from a hall sensor. If tested on meter. Wiring is correct for yose and throtle feeding back increased voltage when pushed...

One other thing. I dont have break sensors attached... this would hardly disable throttle input would??? Thanks

Ok wiring on Throttle is correct and tested working properly but still not working. So its either a setting of this control box is not able to take a throttle. I cant find any information about it unfortunately

Cant it just be cut and wires swapped and electrical tape back? Cheers

I purchase a used bike with yose power pedal assist kit installed. The controller has plenty of 3 pin inputs and im sure this bike had a throttle on it at some stage. I purchased a 3 pin throttle but nothing..... is this even possible to do.. is there a setting I must select on the Display? Ive...

As the title says. Bag that holds battery is a bit tatty and I want to replace. The only triangle cases I can find are material. Why the hell is it so difficult to find a hard shell box. Anyone any ideas where these can be got? The must exist... if not someone is missing a big opportunity to...

I need to but back together Fiido throttle after replacing hall sensor. Im haveing difficulty with the spring and lining up magnetic correctly. Can anyone explain how it goes back together and which direction the spring goes Many Thanks

Yes you are correct. Disconnected the shorted PAS sensor and got E04. Start messing around with throttle for about 5 mins and the wheel all of a sudden start spinning. Throttle not working properly but at least found fault. Wont bother with the Pas sensor any more. But throttle appears to be...

Pedal assist sensor pulling voltage down on throttle output voltage. There is a short on the PAS.... anyway to bypass these on the D2S. If leave unplugged get E04 error straight away. Thanks for all your help

The Voltage coming from the controller before it even gets involved with the Throttle. There is around 2.7 volts coming from controller. Red and Black. Not measuring the feedback signal voltage. Shouldn't it be providing 5vs to the throttle?