Search results

  1. billyboya

    broken cable help

    I seem to now be getting proper readings on the mosfet tests as I have now set meter to 200 ohm mode. I will test again and get back to you. Tomorrow
  2. billyboya

    broken cable help

    ok I will do this later, but just feel this has been going on a good 3 months, But as long as you dont mind helping I do appreciate it lots. are mosfets easy then to replace I cant seem to find which wire is the ground one. I have a cut out switch with a green/yellow wire which goes to the...
  3. billyboya

    broken cable help

    I do apologies for all this but Im nearly getting to the stage of calling a scrap dealer, as I honestly thought after all this time, it was ok. I go for 1st dam test drive after 3 months of fixing it. go just less than 1/4 of a mile only for cable to twist and break. Im afraid Nealh you will...
  4. billyboya

    broken cable help

    I have just removed phase wires from the junction box what go to controller, and wheel does turn freely, but if you touch 2 phase wires together on the cable then it seems there is a brake sticking but obviously no brakes fitted as of yet, its a test I learnt on youtube to test phase wires
  5. billyboya

    broken cable help

    I have just fitted wheel temp to test a new throttle, now when you press down on throttle back wheel locks up, cant really understand this now as it worked fine before, it dont even run now I soldered the 3 phase wires blue to blue, green to green, and yellow to yellow. also soldered 5 sensor...
  6. billyboya

    broken cable help

    do you mean this. do it make a seal to stop nuts turning https://www.ebay.co.uk/itm/224595797056?
  7. billyboya

    broken cable help

    if you look at my profile its an Erider model 15
  8. billyboya

    broken cable help

    What you on about, I didn't realise at 1st what you meant, as I'm not all that good at this stuff sorry you feel that way, but thanks anyway
  9. billyboya

    broken cable help

    Whats a rear hub motor kit. its a electric moped I think why this cable twisted was because on the opposite side of wheel I never had any rotation or torque washers I maybe wrong
  10. billyboya

    broken cable help

    Hi would this do to clean threads, as I dont have any choice to do it another way. I believe the axle is 14mm https://www.ebay.co.uk/itm/383298803044?
  11. billyboya

    broken cable help

    ok I will remove that tie then. yes I have cable tied inside motor wires. I will also like you said leave a loop at axle end then just cable tie to frame. yes also I have added a blob of grease/silicon to outsides of motor case https://www.ebay.co.uk/itm/123126491591
  12. billyboya

    broken cable help

    Yes they said they will check there stock, Ive already got the bolts for them ok I'm with you now so you say its best not to have that grommet at top of cable, do this look better now To be honest I cant remember now
  13. billyboya

    broken cable help

    But on cable side I did have that black torque washer tied with a cable tie in the hole plus had also a anti rotation washer too. But obvious nothing on opp side of axle so would that have caused all this
  14. billyboya

    broken cable help

    Oh so you think its a bad idea, having a grommet at top of axle hole, as I thought it would help cable I have asked Erider for another torque washer like this one, as I only have 1 on cable side, they said they will check in stock if they have any, But do you think its best to get the...
  15. billyboya

    broken cable help

    I’m still bit amazed how that axle managed to twist the cable as it had a anti rotation washer, on axle plus also the torque washer too which was tied with cable tie as well But it must have been like you said
  16. billyboya

    broken cable help

    Nar it will never wear thin lol
  17. billyboya

    broken cable help

    Sorry I meant torque arm not washer. "We all make mistakes, as the hedgehog said to the wire brush" :D
  18. billyboya

    broken cable help

    its about 8cm long that washer, I will see what I have in tool box if not ask erider or like you said a place where i can get one I am extremely grateful for the help you all giving,
  19. billyboya

    broken cable help

    No I have never had a bolt in that hole near dropout for that black torque washer. I take it then you are a engineer, as no way can I make one of those. I will ask erider. But cant a similar thing do same job
  20. billyboya

    broken cable help

    Yes as there are already a hole each side of both dropouts for that washer on the left but I only have one of those washers where can i get another, as I dont see any same on ebay