Search results

Yikes! not what you wanted to find under the old holder.. grinding it down would be my last option tho, where abouts on the new slide is it obstructing, while a clear pic of the 'nub' its not clear where on the tube its sitting..

Indeed the brake lever motor cut off is an instant OFF for the motor while there is a delay between stopping pedaling and the motor cutting off. Also negotiating obstacles in the rd can sometimes benefit from cutting the power momentarily while you snake past obstructions where power from the...

In addition to the controller/display you will also want a pas cadence sensor, and probably at least one brake sensor, to kill the motor when brakes are applied. an additional wiring loom to extend controller connections to the handlebars may also be required. some pas sensors can require the...

@about 2 1/2 mins thet describe the power port. and why you should not undo the screws beside it ;)

130+miles 'in the tank' !! Now your talking..

While waiting for your own post to get approved.. If your battery is still under any warranties. same as above applies ;). chase those down first...

Yes as long as the draw from the rear lamp is just a few ma, I had a quick scan of the ebay ad and failed to see any watt or a/ma rating for the lamp? have you measured the load?? or did i miss it? And as long as the total draw once the leds have warmed up is less than the controllers light...

:) cleaning, filling the holes with plastic putty and re-drilling central pilot holes Works!!!!! Plastic putty arrived this morning and a quick fit later im very happy and have put in an order for the full set of replacements.. Working the putty just as its cured at the 20 min mark means its...

Welcome, Wisper have manuals on the site you may need to delve deeper for older models?? If no joy there post pics of the brakes you want to adjust and their levers.. IF no one from Wisper has dropped in here by monday pm to respond to the display probs, drop them an email or call them...

Cheers @lenny on reflection it was the bathroom window locking/latching mechanism which also needed complete replacement due to rust that was the tricky element to source last time round, i recall the hassle and not the detail so much ;). What threw me with this job was the multiple...

Thanks.. I looked into it a Long time ago, my roof /house faces almost dead east and was initially advised only the south facing slope of the roof was suitable for panels. As any panels on the east or west facing slopes would only work in the morning or afternoon?? Thus at the time the benefit...

Yes BUT you need to be mindful of the current limit of the transistor switching the light circuit on and off. If you attempt to draw more current than the transistor can handle you risk blowing it and any knock-on or side effects that may have on the controllers performance. Its a lot safer...

Investigation will probably require you to start by checking the voltage of the batteries cells which would void any warranties outstanding, so if still under warranty i would request advice from the supplier to start with..

DOH!! must have overlooked that in my state of confusion.. After searching for strong plastic fillers, and getting past the modeling clays, i found JB-Weld Plastic Putty, cures in 20 mins once mixed which was a concern with standard jb weld with its 24hour cure period. superglue+baking powder...

Cheers, I have watched a few youtubes.. the problem is the frames have 2 sets of hinge screw holes already?? bad 1st fit?? and the usual technique of fitting to the corner edge requires new holes/screw positions that will result in zero support/holding capacity without repair of the upvc or...

what happens if your feet slip off the pedals at speed with a bafang bbs mid drive motor? I get winded just at the thought of all that high speed pedaling even if only nominal input is required.. Since my bike is no lightweight and neither am I on the flat the added mass of motor and battery...

Nothing to do with e-bikes, sorry.. so if mods decide to wipe this- cest la vie.. Im stuck replacing the hinges in some upvc windows that no longer open/close easily. The new hinges on the 1st window attacked need fixing in new screw holes right next to the current holes - so close that if...

Perhaps dont give up? I can get you started on determining the 5v and ground connections in the plugs.. you just need a multimeter (£10 ebay/amazon) and some short lengths of thin stiff wire to probe the female socket pole holes.. for test wires i found the snipped legs of electrical...

What if anything have you configured in the controller settings for your motor, Out of the box some expected features may not be enabled until set.. iirc my kt controller was not pas enabled out of the box for example.. and iirc parameter C2 needed attention too.. and when it came to the...

if considering solar who is good to talk to/buy from? Ive had a few cold calls on the landline that did not inspire much confidence and dont know anyone local who has taken the plunge, except for the one unfriendly neighbor.. (took a parcel misdeleverd to me round b4 christmas and got shouted...