Search results

moter 350w controller 15w (but have done shunt mode) the moter rpm info seems to have disappeared from the website. not tried top speed of throttle specs say 22mph max, with bike on stand throttle gave 22 mph no load speed

my 13ah dolphin 15 miles covered , multimeter reading 38.6 I recharge 12 miles covered yesterday multimeter reading 37.1 battery has only done 1000 miles. I fitted my 17ah yosepower which is new about 70 miles on it. now I can tell a difference pas 2 is much more usefull, I can trundle...

hi all yesterday 11hilly miles covered lcd3 loses one bar but pas 4/5 and throttle used down to one bar at 16 miles. so recharged and did 5 miles in mode 3 flattish and find I am down to 3 bars, at 12 miles I am down to one bar? throttle set to 25kph on flat reads 430 watts same as pas 5. the...

thanks daffy 99 my all up weight is similar at 120kg but I see you use throttle to get up to 25kph and then peddle at 28kph+ I rarely peddle faster than 25kph so have to use pas all the time. will try pas 3 tomorrow as I nearly always used (medium pas on the 250 set up)

hi all I have been out today trying out the 350w hub on some local short but steep hills, on some hills the 350 seems easier than the original 250w rear hub but overall I seem to be about 2 mph slower? I definitely like the full speed throttle compared to the original assist up to 6mph one...

first ride on kudos vita uno with elifeshop 350w rear hub. set throttle to p4=1 so I have to peddle to engage thumb throttle speed set to 25kph old freewheel shimano megarange 14-34 7 speed , new 14-28 (I normally would use 32f 14 rear on old set up) tried a few different pas levels all ok...

hi all disconnected all leads and refitted, all seems ok test ride all is fine. let the display auto shut off after 5 mins and then power up lcd with me dismounted, then rode bike and have correct level of assistance. however for some reason my distance covered shows 16.3 miles but I have...

hi anders could you please post a picture of how you have run cables on your doner bike I cani see controller /or bag from pic. my frame is smaller but I seem to have a lot of excess cable? thank you

speed reading mph ok what I used to do was go to shops leave display on/ after 5 mins it auto shuts down would turn on display adjust pas level , sometimes it would give correct assist level. other times It would give problems. recently I simply switch of battery if I am going to be over 5...

hi all can someone post a pic of there bike if the controller with juillet cables was used , I'm having a tough time trying to figure out where to run the cables and best place to mount controller not sure the supplied bag will do the job. ive got enough cable for a tandem thank you

hi ever since ive had my tdz2 I have had the same annoying problem which is the display shuts down if not used after 5 minites, and when I ride the bike again it does not always give the correct level of assistance its like being in eco mode and this absolutely kills my legs normally I have...

d8veh I have 2 ebikes each will have dolphin o9 battery mounts. and will be able to swop 13ah and 17ah batteries between the 2. I have ordered a enerprof 13.8ah softpack from Germany which I have yet to receive which has xt60 connecter and has mj1 cells. I want to compare the softpack vs...

hi all I need more practise cheapo 100w iron ordered from ebay I assume these are the (insulated xt60) I have on closer inspection realised they have a divider so pos and neg cannot touch. no prizes for that's not the best soldered xt60 I have seen

hi all a couple of weeks back had a practise run on soldering an xt60 with 14g wire, xt held in a pair of pliers soldering iron maplins 30w but increases to 130w when the trigger is pressed was not a success pin got hot and partially melted plastic. a few you tube vids re soldering xt60, it...

thanks nealh I do not want to put battries in series , but cables are long and 3 of the batteries have different connecters bullet/xt60/ and another type. trying to standardise connectors to xt60? but having tried to solder a xt60 with the 14g lead from the battery carrier or to renew the...

i have the amazon tail light one which was quite stealthy as it fits under the seat and only realy used the flashing rear light function, but it is akward to remove and charge. and was hidden from view with the seat rain cover pulled down over the unit. I recently bought a lidl saddle but...

thanks nealh and d8veh moter cable not fully home. pas and throttle working ok set to 32kmp no load speed throttle 20mph. now I need to sort out cable run but am unsure about the battery lead and controller battery lead , which are to long. the battery mount that's fitted suits dolphin 09 ...

thanks nealh I got a reply re the six pin throttle was not suitable so getting rebate . if it will fit the yosepower 350w juilet cable as we both have same kit I will buy it of you but have no idea on the pm side of things thank you

hi all have hit a problem similar to petebike post re throttle. I decided to test my 350w kit with lcd3 no brake sensors fitted/pas not connected. lcd displays comes on fine I set speed/wheel size etc and set p4-0 normal throttle. tried throttle nothing working, then realised the lcd3 was not...

thanks d8veh re info, did not think about the extra washer option. I have a tdz2 cd moter on a subway one with thumb throttle,next to the throttle is a wireless gadget with a lever, which operates rear light with left/right directional arrows. whilst pushing the bike on a narrow pavement next...