Search results

my collection of xts for most occasions, actually got quite good at soldering them in the end the one on the left is parrellel lead of ebay for linking 2 batteries

nealh someone I met a while back has 3 yosepower 17ah batteries , exactly the same as my 17ah yosepower and uses with 3 ebikes. 250w yosepower front moter kit and got about 35 miles on smallish doner bike pulling a trailer on the flat. but he is light at about 11 stone. saw him...

hello all my m8 has orbea with shimano steps 500 and I believe the battery is described as 400 w he is thinking of carring a spare 400w as he is going to be doing some rather long rides. so I thought I would ask on the forum if there is a source for shimano or pattern battery (400w)...

I can now answer the above. I took the 350w ebike and 13,8+17ah battery ,locks /drink etc the outward route was hilly so I was often in pas4 and the bike started to play up as regards pas at 22.5 miles , down to 1 bar . swopped to 13.8ah battery , outward journey 23.3 miles./ return...

my local lbs sells orbea, and the mechanic said there are some orbea road ebikes coming out soon that would be fairly light weight and in the region of about 2k, this was about 4 months ago. I went to the shop to see the orbea gain , but was told the shop had not even seen one in the flesh as...

hi all I used to be in a local cycle club, but left as I was always way behind on hills, and sometimes they thought I must have a puncture. a m8 has recently joined the same club and often rides 50 miles or more mostly on unpowered bikes. he also has a orbea keram 30 ebike , but he is...

video here , not sure if the one in email was sent?

thanks woosh , I am not sure exacltly where the "play is" can only detect movement with chainring /spider attatched. no transport so whats the best way of sending tdz2 to yourselves for repair and who to contact by phone/email thank you

thanks woosh I might have to send moter to yourselfs but as its heavy I would think postage would be expensive? having had a look at the moter off the bike I notice it has csk30p stamped on the case, which is a bearing described as a freewheel or sprag clutch bearing 30x62x16mm, not sure...

hi all my tongshen tdz2 250w fitted to Carrera subway has now done 3300 miles and the drive train is noisy. checking the chain it is within wear limits, but I noticed there is about 2mm of movement if I grip the moter chainring at 9 &3 oclock back and forth I thought it...

nealh yesterday after posting the above, I fitted my fully charged 17ah yosepower bought jan 2018. the 15amp supplied controller I tested on the flat it drew 430watts , the 17amp one 530watts, on a local steepish hill I which I only got half way up on my bosch active line the...

hi all yesterday changed over 15amp controller to 17amp 36/48 with 350 moter wheel. a brief ride ,all, was ok ,but throttle sticking, gave4v a liberal squirt of wd40. today a longer ride 10 miles ,I try pas 2/3/4/5 al;l ok the thnrottle then ceases to function just get a (grumble from...

thanks all even looking at es, does this tester check pas for faults?

nealh the square wave 36/48 350 kt controller is sensorless so I only needed to fit the 3 phase wires, I used the short female lead of my original 15amp controller which I fried due to shunt mod, to fit the 36/48 square wave my main interest was to see how much extra the 17amp controller...

hi all at last managed to fit the kt square wave 36/48v to 350w rear hub moter kit. I could not resolve the pas turning the moter wheel in reverse, I tried switching the phase wires over with each other but that did nothing. in the end I turned the kt v12l pas around 180 degrees ,so splines...

yes 9v battery in tester and unit turned on, left hand side,lower middle power led is lit. blue/green/yellow c/clips called moter coil on tester connected to phase wires on lead, spin moter wheel forward/reverse , no leds light up. or is it controller main wire also green /ye;llow/blue? on...

hi all I bought one of those ebike controller testers a short while ago. I have problem with getting the pas to work on kt 36/48 controller/lcd3 /pas kt v12l everthing works with original 15 amp controller setup , julet connections. according to the tester manual it seems turn on tester...

no lcd connected , battery to controller, pas was not rotating , did not give that a thought./ cannot use the pas that came with kit and is working, because its julet connecter, new 17amp controller has the jst type

I went into a local lbs that do Raleigh ebikes, they only had the pioneer front wheel drive on show. I asked about the newer updated bosch moter active line plus (50nm) which has the large front chainring vs the smaller front sprocket of the older models. it appears both are avliable 2018...

thanks ajax looking on psw power for controller wiring the pas wires are black (gnd) brown 5v+ yellow signal the pas sensor has the same colour coding. with battery connected to controller, my multimeter set to 20v dc, black probe to black gnd wire, red probe to brown I could get no...