Wanted someone in england to wire up my ca3

[doggydowg]

Hello

I've recently bought an ebike it has a 24fet green time controller with a cycle analyst plug installed.

I've bought a cycle analyst 3 and it reads all of the signals like voltage and speed etc.

The throttle was wired directly into the green time xontroller , I've had a plug fitted to my throttle so it goes straight into the cycle analyst.

The ca reads throttle in and out but the hub is not getting any power.

I've tried reading up about chopping green signal wires etc but tbh it might as well be in Spanish.

If anyone is capable of wiring my throttle through my ca so I can make use of the limiting ability's and slow this death trap down I'll gladly pay for your time.

Send me a message I'm based in England Portsmouth and can bring the bike to you. Thanks.

 

[Fordulike]

Hello

I've recently bought an ebike it has a 24fet green time controller with a cycle analyst plug installed.

I've bought a cycle analyst 3 and it reads all of the signals like voltage and speed etc.

The throttle was wired directly into the green time xontroller , I've had a plug fitted to my throttle so it goes straight into the cycle analyst.

The ca reads throttle in and out but the hub is not getting any power.

I've tried reading up about chopping green signal wires etc but tbh it might as well be in Spanish.

If anyone is capable of wiring my throttle through my ca so I can make use of the limiting ability's and slow this death trap down I'll gladly pay for your time.

Send me a message I'm based in England Portsmouth and can bring the bike to you. Thanks.

You might get more response if you post this in the ' UK off-road, S Pedelecs and overseas ' section.

That's one beast of a controller. No wonder the ride is urmmm... entertaining

 

[doggydowg]

Thanks for the reply Fordulike yeah its mental apparently has 10k peaks I rode it in park and it wheel spun on the pavement and that was at 6000watts highest recorded power for the ride so god knows what 8-10k would be like ha.

 

[Cyclezee]

Hi Doggy,

Have you tried this, it works with the V2.3 CA-DPS connected to an eZee controller and system.

 

[doggydowg]

Hi Cyclezee

Are those screens from aa v2ca?

Mine is a version 3 and I've just scrolled up and down the menus and can't find advanced. I have set limit at 20amps, speed at 15mph and max power 1000.

I have wired the throttle straight into the controller again, should I rewire the throttle straight into the ca and put in the settings you have suggested in the throttle options?

Many thanks for the reply.

 

[Cyclezee]

Hi Cyclezee

Are those screens from aa v2ca?

Mine is a version 3 and I've just scrolled up and down the menus and can't find advanced. I have set limit at 20amps, speed at 15mph and max power 1000.

I have wired the throttle straight into the controller again, should I rewire the throttle straight into the ca and put in the settings you have suggested in the throttle options?

Many thanks for the reply.

Those screens are for the V2.3, I don't know how the V3 differs.

With the V2.3 I have the throttle directly connected to the controller.

Also have a look at this
https://endless-sphere.com/forums/viewtopic.php?p=571345#p571345

 

[doggydowg]

Hi Cyclezee

I've followed through the set up manual and I've also tred turning aux volts off with throttle wired first to ca and then to controller to no avail.

I get the voltage reading on the cadp on the green wire, so the ca is sending the signal but from what I've read a diode needs to. W bypassed or something along those lines.

I'll pray that someone is out there who can sort this out for me. Thanks for the links a and pics.

 

[Cyclezee]

Hi Cyclezee

I've followed through the set up manual and I've also tred turning aux volts off with throttle wired first to ca and then to controller to no avail.

I get the voltage reading on the cadp on the green wire, so the ca is sending the signal but from what I've read a diode needs to. W bypassed or something along those lines.

I'll pray that someone is out there who can sort this out for me. Thanks for the links a and pics.

Sorry it's not happening, to be honest, you might be better posting on Endless Sphere for answers

 

[doggydowg]

Sorry it's not happening, to be honest, you might be better posting on Endless Sphere for answers

I've wrote there too thanks the.

 

[Fordulike]

Hi Cyclezee

I've followed through the set up manual and I've also tred turning aux volts off with throttle wired first to ca and then to controller to no avail.

I get the voltage reading on the cadp on the green wire, so the ca is sending the signal but from what I've read a diode needs to. W bypassed or something along those lines.

I'll pray that someone is out there who can sort this out for me. Thanks for the links a and pics.

As John says, try posting your questions on Endless Sphere. Not many members on here have a great deal of experience with the CA V3.

There are more members over there, that connect these displays to monster power controllers and motors.

Not read through, but might be a few snippets of info here:

http://www.ebikes.ca/product-info/cycle-analyst-3.html

Stick around here though. You never know, someone might come up with the solution.

 

[doggydowg]

Thanks Fordulike for the link I've spent past few days reading that file over and over.

Let's hope someone comes along ;-)

 

[Fordulike]

This topic has moved over to the ' UK off-road, S Pedelecs and overseas ' section:

http://pedelecs.co.uk/forum/threads/wanted-someone-in-england-to-wire-up-my-ca3.22854/#post-286359