Recommendations LCD display and Controller for front hub 240W 29Nm 36V

[SilverTurfer]

Hi Pedelecers, does anyone have any experience or suggestions to control & display
for front hub 240W 29Nm 36V

What I'm looking for primarily is something that is reliable and mainstream.

Why am I after this?

I've got a Gazelle Innergy from 2009, but I'm going to replace all the control stuff but keep the motor.
As described at:

Gazelle rebuild

Here, I share technical solutions that arised during the development of my solar-bike.

www.avdweb.nl

Grateful for any advice.

 

[Nealh]

Buy a KT (Kuenteng ) 24/36v controller and a lcd there are 4 models to buy lcd3, 5 or 6 and comes with all the ancillaries you need. Delivered to your door for about £80 or less.

7.17￡ |24V/36V 250W 15A Brushless DC Sine Wave Controller +LCD or LED+Throttle+Brake Lever+PAS + Speed Sensor+light speaker+switch|lcd 36v|controller controlspeaker speaker - AliExpress

Smarter Shopping, Better Living! Aliexpress.com

www.aliexpress.com

 

[SilverTurfer]

Cheers Neal,
I'm going to have a poke around with my current setup to make sure I've got the right number of wires going to the motor etc.
Its a shame there is such a long lead time getting this stuff in from China.
But thank you, I'm looking forward to reporting back on the success of this project.

 

[Nealh]

The delivery dates are a guideline usually most stuff arrives within 14 days. My last item I ordered arrived Friday last, seven days from placing the order.

From the controller link you gave it shows the motor has 9 pins outs so a sinewave/sensored hub. But always worth checking motor to confirm first.

 

[Nealh]

You can probably buy other controllers 24v, though KT ones are the most user friendly after market ones available.
So you don't buy a lemon check back here to confirm an item/s are correct for your needs.

 

[SilverTurfer]

Cheers Neal,
I'm going to go out now and have a good look at my Gazelle Innergy and have a deeper poke at it.
If the misses does not find me something more useful to do.
Back later.

 

[harrys]

Here in the USA, I find it's a little less money ordering from the pswpower.com site and I get to use paypal, which I prefer to putting a credit into aliexpress. I ordered a LCD3 7 days ago. It is suppossed to be in transit, but the chinese tracking numbers don't tell us much, other than it's "in transit".

I like the KT brand. I have a few, but did have one controller not work right, but I waited 4 months to use it, so I never bothered to test their customer service.

You might consider a 36/48V unit . Might have better safety margins for the components.

 

[SilverTurfer]

Cheers Harry for your input,

I still have not got around to ordering my kit. I've had a few distractions over the last few days.
On closer inspection I'm concerned now about the front wheel motor hub.
When I spin the wheel backwards it makes a noise.
I don't know if that's OK or there is is a problem in that bit now.
I would have thought that if it was a bearing it would have made a noise in both directions.
Anyone got any ideas on this?
I think I'll put that question on another thread.

 

[Woosh]

When I spin the wheel backwards it makes a noise.

that's normal you hear the noise and feel the resistance.
Spinning backward engages the clutch and forces the rotor to turn.

 

[SilverTurfer]

Cheers Woosh,

You have cheered me up no end, thanks.
At least I don't think I have to worry about that bit now.

I see you have a picture on your website home page of something very similar to my Gazelle Innergy?

 

[Woosh]

I fixed Emily Joy's Gazelle Innergy sometime ago, it was a one off job.
I added a Lishui controller and a LED panel to run the motor.
The main difficulty was to preserve the existing wiring.
If I had to do this again, I would use the torque sensor controller.
http://wooshbikes.co.uk/?tskit

 

[SilverTurfer]

I think I'll be giving you a ring Mr Woosh