connector help
- Thread starter billyboya
- Start date
'Ring terminals'
Ring Terminals for sale | eBay
Find great deals on eBay for Ring Terminals. Shop with confidence.
www.ebay.co.uk
No I mean the yellow block connectors not the rings look at bottom image its so you can screw the ring connecters on those threads and tighten with nuts
thanks but all I get on ebay is these which isnt what I want
https://www.ebay.co.uk/sch/i.html?_from=R40&_trksid=p2334524.m570.l1313&_nkw=3-phase/brushless+motor/controller+junction+box.&_sacat=0&LH_TitleDesc=0&_odkw=6+ring+block+connectors&_osacat=0
JUNCTION BOX FOR ELECTRIC CONTROLLERS EBIKE | eBay
Find many great new & used options and get the best deals for JUNCTION BOX FOR ELECTRIC CONTROLLERS EBIKE at the best online prices at eBay! Free delivery for many products.
www.ebay.co.uk
brushless junction box - Google Search
www.google.com
brushless junction box - Google Search
www.google.com
JUNCTION BOX FOR ELECTRIC CONTROLLERS EBIKE | eBay
Find many great new & used options and get the best deals for JUNCTION BOX FOR ELECTRIC CONTROLLERS EBIKE at the best online prices at eBay! Free delivery for many products.www.ebay.co.uk
brushless junction box - Google Search
www.google.com
brushless junction box - Google Search
www.google.com
wow that's it many thanks mate much appreciate it
A little off topic on this one but did you Billy carry out hall sensor testing on your hub motor ?
Hi Nealh I'm afraid I haven't touched moped until today as got fed up fixing it. But back onto it again. But have forgot now what to do as been told to check Phase wires but not connected and was told black probe go to ground and then red to green phase wire.. but which is ground as I have tried black probe in the battery N slot on moped what plugs into battery but no readings at all there is a black wire from controller too but even tried that cant get no reading so maybe I am not touching ground
Btw I received a new controller from Erider But not sure where all wires go now I think I have explained right
Ok now I think this is right wires with red circle must be hall wires as there is 5
the plug in pink circle I don't know where that go its 4 pins
the plugs in yellow circle I think go to the alarm as that's 2 connections
the black mark I think those 2 are to replace 2 plugs what come from controller and go into wiring loom
the light green circle I think is the throttle as 3 wires black red and blue
the dark blue are battery power leads
and the light blue are the 3 phase wires
would this be correct
and I think the 2 white wires you join for learning
I found this page too which is handy but Im stuck on Phase wires which is the ground
Troubleshooting - Learn
One of the things about meshing complex electrical and mechanical systems together is that occasionally things can go wrong! We've seen more than our fair share of ebike issues come and go over the years - from shot ball bearings, seized freewheels and stripped threads to defective hall sensors...
Last edited:
What about the pedal option of PAS ?
Either the light Green or Pink ?
If the Pink group has a White wire I would be inclined to think it may be for a throttle, otherwise you will need E rider to confirm the wire connectors status.
Either the light Green or Pink ?
If the Pink group has a White wire I would be inclined to think it may be for a throttle, otherwise you will need E rider to confirm the wire connectors status.
The pink group has 4 wires green, red, purple, & black
The light green must be the throttle But I wont know which one is PAS as there is no more connections for them to plug into and the only whites wires are those 2 laying across top which I think are learning ones
White wires will be either learn wires or a speed restriction wire.
Ok we will take it then that throttle is the Green group and the pink could or may be is for a torque sensor (which makes more sense with 4 wires).
Ok we will take it then that throttle is the Green group and the pink could or may be is for a torque sensor (which makes more sense with 4 wires).
Later model 15 mopeds may have had the cadence sensor PAS replaced with a TS sensor and you may have the later controller version that supports TS.
Well I e-mailed Erider and there reply was.
light blue = phase
dark blue = power
green = throttle
red = halls sensor wires x 5
yellow 2 plugs for the alarm
black 2 x single wires 1 go to display other go to horn, indicators, and headlamp box on left of handle bars
but now I have a problem as in this image below the throttle wires on left are from controller, are from top black,red &blue but the other part I ordered the wires are same colour but not same order, red,blue,&black so will that matter
But I think I know which are the phase, hall, and power connections are
light blue = phase
dark blue = power
green = throttle
red = halls sensor wires x 5
yellow 2 plugs for the alarm
black 2 x single wires 1 go to display other go to horn, indicators, and headlamp box on left of handle bars
but now I have a problem as in this image below the throttle wires on left are from controller, are from top black,red &blue but the other part I ordered the wires are same colour but not same order, red,blue,&black so will that matter
Red & Black have to match as they are 5v & Gnd respectively, the fact the signal happens to be the same (Blue) is coincidental.
How can I do change them now, as I have bought 5 pairs of those throttle wire connectors JST-SM
I cant see how to change the wires, actually the seller on ebay was displaying red green & white wires but when they arrived they are red, blue, & black wires
5 Pairs JST 3-Pin Plug Connector Cable Wire Male + Female 5 Of Each Connector 7625862676175 | eBay
3 pin JST SM connectors. WHY BUY FROM US! Material:PVC plastic 22AWG.
www.ebay.co.uk
Last edited:
Using a needle one pokes it in the small hole in the end to depress a small barb and at the same time gently pull the wire out from the end other, another option if you aren't easily confused is to use a piece of colour heatsink on each end of the wire to re designate the colour order (one then has to remember to forget about the main wire colour and be guided by the heat sink colour when connecting up).
So shrink a bit of Red each end to the Black wire, a bit of Black to the Blue wire and any colour you like to the Red (middle) wire to donate it is the signal (personally I would use White.
So shrink a bit of Red each end to the Black wire, a bit of Black to the Blue wire and any colour you like to the Red (middle) wire to donate it is the signal (personally I would use White.
Hi Nealh I was thinking of removing each wire like you said. using a pin or needle, I dont have any coloured heat sink so will try needle way then push each back in same order as controller end
bingo Ive managed to remove the wires and line them up to controller end thanks Nealh
Last edited:
Related Articles
-
MTF Enterprises announces acquisition of EMU Electric Bikes- Started by: Pedelecs
-
Wisper 806T folding bike wins Which? ‘Best Buy’- Started by: Pedelecs
-
Sustrans calls for protected cycle lanes- Started by: Pedelecs
-
Amazon launch their first UK e-cargo micromobility hub- Started by: Pedelecs
